Parts list for The Universal 1Watter - 80 Meter Version 5
16 Sep 2016
=========================================================
Items is Bag #1
C6,7,8,9,10,11,13,14,19,27,33,36,37,38,41,44,46,47,48,53
L4        black toroid FT37-43:14T - 11" #27 green
T5        BN-43-2402-8T:2T - 10" #34 red & 4" #30 red
=========================================================

Items in Bag #2
C1        1000p ***
C2        1800p ***
C3        not used
C4        820p ***
C5,23,24,26 - 50p ***
C12,40    10u
C15       47p ***
C16,22,25,35 - 220p ***
C17,39    47n yellow axial
C18       2p2 ***
C20       150p ***
C21       390p ***
C28       12p ***
C29,30,31,32 - 680p labeled 681 ***
C34,50    180p ***
C42,49    47u
C43       33u
C45       33p
C51       56p
C52       2u2 yellow mono cap marked 225
Cs        not included
Cx        not included

D1,2,4,6,7 - 1N4148 red
D3        1N5256B silver 30 V Zener
D5        MV209 varactor TO-92 case
D8        1N5817
D9,10     NPC-127 blue 5.6 V Zener
D11       1N5240B red 10 V Zener

L1,2      T37-1 blue toroids with 17 turns, 13" #26 red wire ***
L3        FT37-61 dull black toroid with 20 turns, 14" #26 red wire ***
L5        FT37-61 dull black toroid with 13 turns, 11" #26 red wire ***
L6        T37-2 red toroid with 13 turns, 11" #26 red wire ***

Q1        2N5109
Q2        PN2222
Q3,6,7    2N3904
Q4        MPSH10
Q5        J310
Q8,9      J113
Q10       2N3906
Q11       2N7000

R1,2      51
R3,9,21,22,25,29 - 470 (R25 only used with no speed pot)
R4        2K2 (2.2K)
R5        500 ohm trim Pot (in hardware Bag #3)
R6        4K7 (4.7K) ***
R7,8,17,18,19,26 - 4K7 (4.7K)
R10       1K
R11       1K5 (1.5K)
R12       1K2 (1.2K)
R13       1M
R14       4R7 (4.7)
R15       100K
R16       10K
R20       500 ohm volume control (in hardware Bag #3)
R23,24    4M7 (4.7M)
R27,28    not installed
R30       500K ohm tune control (in hardware Bag #3)

T1        FT37-61 dull black toroid with 15 turns primary - 12" #26 red wire ***
          and 3 turns secondary - 6" #27 green wire
T2        T37-1 blue toroid with 30 turns primary - 20" #30 red wire ***
          and 1 turn secondary - 4" #27 green wire
T3        T37-1 blue toroid with 1 turn primary - 4" #27 green wire ***
          and 30 turns secondary - 20" #30 red wire
T4        T37-1 blue toroid with 4 turns primary - 6" #27 green wire ***
          and 31 turns secondary - 20" #30 red wire

U1        not used
U2,4,5	  NE602A
U6        LM386N-4
U3,7      78L08
U8        78L05
U9        ATtiny45-20PU Keyer IC version-4

X1        13.560 mHz - from ebay.com ***
X2,3,4,5,6 - 10.000 mHz - Mouser # 815-AB-10-B2 ***

=========================================================
Items in Bag #3
One Heat Sink for TO-5
5 each - 8 Pin Dip Machine Sockets
2 each - stereo phone jacks for headphones and keyer connections
1 each - normally open push-button
1 each - 500 ohm Volume Control - R20
1 each - 500K ohm Tune Control - R30
1 each - 500 ohm trim pot - R6
1 each - BNC Connector

=========================================================
Items in Bag #4
PCB  Printed Circuit Board
74" #26 red solderable magnet wire (15t)
31" #27 green solderable magnet wire (7t)
64" #30 red solderable magnet wire (13t)
10" #34 red solderable magnet wire (2t)

=========================================================
1 each - Power Switch *NOT INCLUDED*
1 each - 10K or 20K or 50K or 100K Linear Keying Speed Potentiometer *NOT INCLUDED*
Universal Interconnect Kit #2 *NOT INCLUDED*
Connector Wire *NOT INCLUDED*
Case *NOT INCLUDED* -See recommendations in the building instructions
4-40 PCB mounting screws and spacers *NOT INCLUDED*
Instruction on How to Solder *NOT INCLUDED*

=========================================================
*** = BAND SPECIFIC COMPONENT

===== changes since V3 ==================================
C52       2u2 yellow mono cap marked 225
D11       1N5240B red 10 V Zener
R15       100K
R26       4K7
R29       470 
R30       500K ohm Tune Control

===================== End of List =======================